Home › Services › Dryer Repair
Gas & Electric Dryer Repair
Dryer Repair in Reno, NV
Dryer running cold, taking two cycles, squealing or not starting at all? We repair gas and electric dryers of every major brand in Reno, Sparks and nearby.
- Gas & electric dryers
- Vent airflow checked
- Written quote first
Dryer repair in Reno: the short answer
A dryer that runs but will not heat usually has a blown thermal fuse, a failed heating element (electric) or a bad igniter or gas valve coil (gas). A dryer that will not start often has a door switch, start switch or thermal fuse problem, and squealing or thumping points to worn drum rollers, idler pulley or belt. All of these are routine one-visit repairs in Reno.
Many of the dryer calls we take in Reno trace back to airflow. Lint packed in a long vent run makes the dryer overheat, trips the safety fuse and doubles drying time. We check the vent path on every dryer repair, not just the part that failed.
Dryer safety first
- If you smell burning or see scorch marks, stop using the dryer and unplug it.
- Clean the lint screen before every load, and check the outside vent hood flap opens when the dryer runs.
- For gas dryers: if you smell gas, leave the house and call NV Energy or 911 from outside.
- Never run a dryer with a crushed or disconnected vent hose behind it.
Dryer problems we fix
Runs but no heat
Thermal fuse, heating element, high-limit thermostat, igniter or gas valve coils.
Takes too long to dry
Restricted vent, failing element, faulty moisture sensor or a cycling thermostat.
Loud squeal or thumping
Worn drum rollers, idler pulley, glides or a drive belt starting to fray.
Won’t start
Door switch, start switch, thermal fuse, motor or control board faults.
Shuts off mid-cycle
Overheating motor or thermostat trips, often tied to lint-blocked airflow.
Gas dryer won’t ignite
Igniter glows but no flame, or no glow at all: igniter, flame sensor or valve coils.
Gas dryers at Reno’s elevation
Reno sits around 4,500 feet above sea level, where the air holds less oxygen. Gas appliances are built for a particular burner setup, and manufacturers publish high-altitude instructions for installations like this one. A gas dryer that was never set up for altitude can burn with a weak flame, cycle more often and take longer to dry.
On every gas dryer call, our technicians check the flame, igniter and flame sensor and will tell you if the installation looks wrong for the altitude.
Simple habits that prevent most dryer calls
- Clean the lint screen every load and wash it with soapy water if fabric softener film builds up.
- Have the vent duct cleaned about once a year, more often for long runs or heavy use.
- Use rigid or semi-rigid metal duct, not plastic or foil accordion hose.
- Do not overload: heavy loads strain rollers, belts and the motor.
Dryer repair cost in Reno
Dryer fixes like thermal fuses, belts and door switches are among the least expensive appliance repairs. Heating elements, igniters and gas valve coils land in the middle, and motors or control boards at the top of the typical Reno range of roughly $99 to $214 reported by HomeAdvisor.
Full price ranges are in our Reno appliance repair cost guide.
Repair or replace your dryer?
Dryers are mechanically simple and often run 10 to 13 years or more. Heat, belt and switch problems are almost always worth repairing.
Replacement makes sense mainly when the drum, motor and control board are all worn on an older machine, or when a cracked drum or rusted cabinet makes the repair poor value.
Dryer brands we repair
- Whirlpool
- Samsung
- LG
- Maytag
- GE
- Kenmore
- Speed Queen
- Electrolux
- Frigidaire
- Amana
- Bosch
- Miele
Gas and electric, standard and stacked units. Need the washer looked at too? See washer repair in Reno.
Frequently asked questions
Why is my dryer running but not heating?
On electric dryers the usual causes are a blown thermal fuse, a failed heating element or a bad high-limit thermostat. On gas dryers it is often the igniter, flame sensor or gas valve coils. A blocked vent is frequently what caused the part to fail.
How long should a dryer take to dry a load?
A normal mixed load usually dries in about 40 to 60 minutes. If it takes two cycles, check the lint screen and vent first, then have the heating system tested.
Is a squealing dryer dangerous?
Usually it is worn drum rollers, an idler pulley or a belt, which is not dangerous right away but gets worse quickly. A burning smell is different: stop using the dryer and unplug it.
Do you repair gas dryers in Reno?
Yes. We repair both gas and electric dryers and check gas flame and ignition on every gas dryer call.
How much does dryer repair cost in Reno?
Most dryer repairs fall within the local range of roughly $99 to $214. Thermal fuses and belts are at the low end; motors and control boards are higher. You get a written quote first.
Appliance down? Get it fixed this week, often today.
Tell us what is wrong and which appliance it is. We will give you a time window, a clear diagnostic fee, and a written quote before any repair starts.